Invacare Mobility Aid 1038599 User Manual

WHEEL LOCK EXTENSION HANDLE  
Assembly,Installation and Operating Instructions  
Kit No. 1038599  
NOTE: Check all parts for shipping damage and test be- 2. Remove the button screw, washer and locknut that se-  
fore using. In case of damage, DO NOT use. Contact the  
dealer / Invacare for further instructions.  
curestheEXISTINGhandletothewheellockassembly.  
3. Attach the looped end of the elastic cord of the wheel  
lock extension handle over the spacer of the EXIST-  
INGhandle.  
SAFETY SUMMARY  
Thefollowingrecommendationsaremadeforthesafe  
installation of the Wheel Lock Extension Handle Kit:  
4. ReassembletheEXISTING handletothewheellock  
with the button screw, washer and locknut to secure  
the cord around the spacer.  
WARNING  
DO NOT insta ll or use this kit without first re a ding  
a nd unde rsta nding the se instruc tions. If you a re  
una ble to unde rsta nd the Wa rnings, Ca utions or  
Instruc tions, c onta c t a he a lthc a re profe ssiona l,  
de a le r or te c hnic a l pe rsonne l be fore a tte mpt-  
ing to insta ll this kit - othe rwise , injury or da m-  
a ge ma y oc c ur.  
NOTE: Cord is made of stretchable material and may be  
adjusted to a light or loose fit to meet the needs of the user.  
5. Push the opposite end of the elastic cord up through  
the slotted hole in the wheel lock extension handle.  
6. Runthecordthroughthewasherandtieaknotabove  
the washer as shown in FIGURE 1.  
Any worn or da ma ge d ha rdwa re MUST be re -  
pla c e d.  
7. Pullthecordbackdownintothewheellockextension  
handle.  
Afte r ANY a djustme nts, re pa ir or se rvic e a nd  
BEFORE use , ma ke sure a ll a tta c hing ha rdwa re  
is tighte ne d se c ure ly.  
8. Install the NEW rubber tip.  
9. SlidewheellockextensionhandleoverEXISTINGhandle.  
Knot (STEP 6)  
Washer  
(STEP 6)  
The following parts are included in Kit No. 1038599:  
Rubber Tip  
(STEP 8)  
DESCRIPTION  
RubberTip  
#10 Flat Washer  
ExtensionHandle  
Elastic Cord Assembly  
Instruction Sheet  
Plastic Bag  
QUANTITY  
Elastic Cord  
(STEPS 3 & 5)  
Wheel  
Lock  
Extension  
Handle  
(STEP 5)  
2
2
2
2
1
1
Spacer (STEP 3)  
Button Screw  
(STEPS  
2 & 4)  
NOTE: If installing this kit on a wheelchair manufactured  
priorto5/93, anewstylewheellockhandlemayneedtobe  
ordered. Contact an Invacare Dealer or Customer Service  
at the number on the bottom of this instruction sheet.  
EXISTING  
Handle  
(STEP 9)  
INSTALLING THE WHEEL LOCK  
EXTENSION HANDLE (FIGURE 1 )  
NOTE:Wheellockextensionhandlescannotbeinstalled  
on high mount wheel locks already equipped with exten-  
sion handles.  
Wheel Lock  
Assembly  
(STEP 2)  
Locknut  
(STEPS 2 & 4)  
Washer  
(STEPS 2 & 4)  
FIG URE 1 - INSTALLING THE WHEEL  
LO C K EXTENSIO N HANDLE  
1. Remove and discard the EXISTING rubber tip on  
the wheel lock handle (if applicable).  
Invacare Corporation  
USA  
Canada  
One InvacareWay  
Elyria, Ohio USA  
44036-2125  
5970 ChedworthWay  
Mississauga, Ontario  
L5R 3T9, Canada  
905-890-8838  
Invacare is a registered trademark of Invacare Corporation.  
©
1999 Invacare Corporation  
800-333-6900  
Form No. 93-40 Part No. 1039644 Rev. C (2) -11/99  
 

Indesit Freezer B 33 FNF X User Manual
Indesit Washer WIB101 User Manual
Ingersoll Rand Door Schlage LiNK User Manual
Inova Computer Hardware ICP PII User Manual
Insignia Tablet NS 15T8LTE User Manual
Jabra Wireless Office Headset GN9330e User Manual
John Deere Lawn Mower GM1048E User Manual
John Deere Saw ET 3410 J User Manual
John Lewis Washer Dryer JLWD 1406 1400 User Manual
JVC Projector G2000 User Manual