Jwin Stereo System JX CD3150D User Manual

MICRO HI-FI CD PLAYER  
AND AM/FM STEREO RADIO  
JX-CD3150D  
 
PREPARATION FOR USE  
UNPACKING AND SET UP  
• Carefully remove the unit from the carton and remove all packing materials  
from the unit.  
• Carefully remove any small strips of tape which may have been used to keep  
the CD door closed during shipment.  
• Open the CD compartment by lifting the “OPEN” tab on right side of  
CD door. Inside the CD compartment you will see a card which is used to pr-  
event the laser pick-up from moving during shipment. Carefully remove  
this card and close the CD compartment door.  
• Please save the carton and packing materials in the event that your unit ever  
needs to be returned for service. The original carton and packing materials are  
the only way to protect the unit from damage during shipment.  
• Unwind the FM lead wire antenna and extend it to its full length.  
• Remove the twist-tie from the AC power cord and extend it to its full length.  
PROTECT YOUR FURNITURE  
This model is equipped with non-skid rubber 'feet' to prevent the product from  
moving when you operate the controls. These 'feet' are made from non-migrating  
rubber material specially formulated to avoid leaving any marks or stains on your  
furniture. However certain types of oil based furniture polishes, wood preservatives,  
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a  
rubber residue on the furniture. To prevent any damage to your furniture we strongly  
recommend that you purchase small self-adhesive felt pads, available at hardware  
stores and home improvement centers everywhere, and apply these pads to the  
bottom of the rubber 'feet' before you place the product on fine wooden furniture.  
2
MS7616_061404.p65  
4
14/6/2004, 10:59  
 
SPEAKER CONNECTION  
Connect each speaker to the corresponding speaker terminals on the back panel  
of the main unit. Make sure that:  
• The left speaker is connected to the (L) left pair of speaker terminals, and the  
right speaker to the (R) right pair of speaker terminals.  
Also make sure that the speaker wires are correctly connected:  
• That the red wires are connected to the red (+) terminals, and the black wires to  
the black (–) terminals.  
Depress the plastic lever to open the terminal, insert the bare end of the speaker  
wire into the opening and release.  
Red Wire  
R
L
+
+
Black Wire  
3
MS7616_061404.p65  
5
14/6/2004, 10:59  
 
POWER SOURCE  
This system is designed to operate on normal 110/220V 60/50Hz AC house  
current only. Attempting to operate this system from any other power source may  
cause damage to the system, and such damage is not covered by your warr-  
anty. Unwind the AC power cord and connect the AC plug to your AC outlet.  
FM ANT  
4
MS7616_061404.p65  
6
14/6/2004, 10:59  
 
LOCATION OF CONTROLS AND INDICATORS  
11  
12  
13 14  
15  
16  
10  
9
17  
18  
19  
8
7
6
5
20  
4
3
2
1
21  
25  
24 23  
22  
5
MS7616_061404.p65  
7
14/6/2004, 10:59  
 
1.) POWER ON  
/ OFF  
Button.  
2.) POWER ‘On’ Indicator.  
3.) VOLUME Control.  
4.) STOP  
Button.  
5.) PROGRAM Button.  
6.) MONO  
/ STEREO  
Selector Button.  
Selector Button.  
7.) Band AM  
/ FM  
8.) Function CD  
/ TUNER  
Selector Button.  
9.) Tuning Dial.  
10.) PLAY / PAUSE Indicator.  
11.) FM STEREO Indicator.  
12.) CD Track Number Display.  
13.) PROGRAM Indicator.  
14.) CD Door.  
15.) OPEN Button.  
16.) REPEAT Indicator.  
17.) TUNING Control.  
18.) REPEAT Button.  
19.) RANDOM Button.  
20.) PLAY/PAUSE  
Button.  
21.) External FM Wire Antenna.  
22.) AC Power Cord .  
23.) PHONES Jack.  
24.) FWD SKIP/SEARCH  
Button.  
Button.  
25.) REV SKIP/SEARCH  
6
MS7616_061404.p65  
8
14/6/2004, 10:59  
 
OPERATING INSTRUCTIONS  
LISTENING TO THE RADIO  
• Make sure that the FM Lead Wire antenna is extended to its full length.  
1.) Press the POWER button to turn the unit ON  
”. The POWER indicator  
comes ‘On’.  
2.) Press the CD / TUNER button to TUNER  
position.  
3.) Press the AM / FM button to select the radio band as desired.  
4.) Turn the TUNING control to tune to the desired radio station.  
Note:  
If you tune to a FM Stereo station and the MONO / STEREO button is set  
to STEREO  
position, the FM STEREO indicator  
PROGRAM  
FM STEREO  
will light.  
PLAY/PAUSE  
REPEAT  
If the FM reception is noisy or weak you may be able to improve it by  
pressing the button to the MONO  
position, however the sound will no  
longer be in stereo.  
5.) Adjust the VOLUME control as desired.  
6.) When you are finished listening press the POWER button to the “OFF  
position. All indicators go ‘off’.  
7
MS7616_061404.p65  
9
14/6/2004, 10:59  
 
HINTS FOR BETTER RECEPTION  
FM: The FM lead wire antenna on the back panel should be extended to its full  
length. You may also have to vary the direction of this antenna until you find  
the position that provides the best reception.  
AM: The AM bar antenna is inside the cabinet of the main unit. You may need to  
change the position of the main unit until you find the position that provides  
the best reception for your favorite AM stations.  
FM STEREO  
PLAY/PAUSE  
PROGRAM  
REPEAT  
FM 88  
92  
98  
102  
106 107 108  
MHz  
AM 530  
600  
800  
1000 1200 1400  
1700 KHz  
TUNING  
CD TUNER  
AM FM  
MONO STEREO  
PE  
PLAY/  
STOP  
PAUSE  
POWER  
PHONES  
REV.  
FWD.  
SKIP/SEARCH  
ON  
OFF  
8
MS7616_061404.p65  
10  
14/6/2004, 10:59  
 
PLAYING COMPACT DISCS  
NOTE: Although this CD player can read CD-R and CD-RW discs, in addition to  
normal CDs, the playability of CD-R/RW discs may be effected by the type of  
software that was used to create the discs, as well as the quality and condition of  
the blank media you are using. 100% playability cannot be guaranteed.  
This is not an indication of a problem with the player.  
NORMAL Playback  
1.) Press the POWER button to turn the unit ON  
”. The POWER indicator  
comes ‘On’.  
PROGRAM  
FM STEREO  
2.) Press the CD / TUNER button to CD  
position.  
PLAY/PAUSE  
REPEAT  
The two dashes “ – – ” light up on LED display.  
3.) Open the CD door by lifting the OPEN tab on right side of CD door. If  
you have not already removed the card from the CD player, please remove it  
now.  
4.) Place your CD on the center spindle with  
the printed label side facing up. Make sure  
the CD is seated properly.  
Close the CD door.  
PROGRAM  
REPEAT  
FM STEREO  
PLAY/PAUSE  
The player will read the Table of Contents and the  
display will show the total number of tracks on the  
disc.  
If the disc is damaged or up side down, display will show – – ”.  
9
MS7616_061404.p65  
11  
14/6/2004, 10:59  
 
5.) Press the PLAY/PAUSE  
button to begin playback on Track 1.  
PROGRAM  
REPEAT  
FM STEREO  
The PLAY/PAUSE indicator lights up.  
PLAY/PAUSE  
6.) Adjust the VOLUME control as desired.  
7.) Playback will continue until the end of the disc. When the disc ends the display  
again shows the total number of tracks on the disc.  
You may also stop playback at any time by pressing the STOP button.  
PAUSE Control  
To pause momentarily during playback press the PLAY/PAUSE  
button again.  
PROGRAM  
FM STEREO  
Playback stops but the disc continues to spin and the  
PLAY/PAUSE  
REPEAT  
PLAY/PAUSE indicator flashes.  
Press the PLAY/PAUSE  
button once more to cancel Pause and resume  
playback. The PLAY/PAUSE indicator stops flashing.  
Skipping Tracks and High Speed Music Search  
During CD Playback, repeatedly press the SKIP FWD  
or SKIP REV  
button  
to skip to higher or lower number tracks. When the desired track number appears  
on the display release the button and playback will begin on the desired track.  
To rapidly search forward or back within a track to locate a specific musical passage,  
depress and hold either the  
/
buttons.  
The player will move forward or backward at high speed as long as the buttons are  
depressed. When you hear the desired passage release the buttons. Normal  
playback will resume at that point.  
10  
MS7616_061404.p65  
12  
14/6/2004, 11:10  
 
REPEAT Playback  
This feature allows you to continuously repeat a single track or the entire disc.  
To Repeat A Single Track  
PROGRAM  
FM STEREO  
Press the REPEAT button once. The REPEAT indicator  
PLAY/PAUSE  
REPEAT  
flashes.  
Press the  
or  
buttons to select the desired track. Press the PLAY/PAUSE  
button to begin Repeat Playback of the selected track.  
PROGRAM  
REPEAT  
To Repeat The Entire Disc  
Press the REPEAT button twice. The REPEAT indicator  
remains ‘on’.  
FM STEREO  
PLAY/PAUSE  
Press the PLAY/PAUSE  
button to begin Repeat Playback of the entire disc.  
To cancel Repeat Playback press the REPEAT button until the REPEAT Indicator  
goes ‘off’.  
Repeat Playback is also canceled by pressing the STOP  
button, or setting to  
the TUNER  
position.  
11  
MS7616_061404.p65  
13  
14/6/2004, 10:59  
 
PROGRAMMED Playback  
This feature allows you to program up to 20 tracks on a disc for playback in any  
desired order.  
Note: You cannot program tracks while a disc is playing. If the disc is playing  
press the STOP button first before beginning the programming steps below:  
PROGRAM  
REPEAT  
FM STEREO  
PLAY/PAUSE  
1.) Press the PROGRAM button to enter the Program  
Mode. The PROGRAM indicator and Program  
Number ‘0’ flash.  
2.) Press the SKIP  
or  
button to select the first  
PROGRAM  
REPEAT  
FM STEREO  
PLAY/PAUSE  
track number you wish to enter in the program  
memory.  
Example: Track Number 8.  
3.) When the desired track number appears on the  
display, press the PROGRAM button again to enter  
that track in memory.  
PROGRAM  
REPEAT  
FM STEREO  
PLAY/PAUSE  
The Program Number display returns to flashing “0”.  
4.) Repeat Steps 2-3, selecting a different track number each time until you have  
entered up to 20 tracks in the program memory.  
Note: You may program the same track number to  
PROGRAM  
FM STEREO  
play multiple times in the program sequence if  
desired. When programmed track is full, “ – – ”  
flashes in the display.  
PLAY/PAUSE  
REPEAT  
5.) Press the PLAY/PAUSE  
button to begin  
PROGRAM  
REPEAT  
FM STEREO  
PLAY/PAUSE  
Programmed Playback. The PROGRAM indicator  
flashes. Playback will begin with the first track you  
programmed and will continue until the last  
programmed track has played.  
12  
MS7616_061404.p65  
14  
14/6/2004, 10:59  
 
6.) After the last track has played the player stops and the display shows the total  
number of tracks on the disc. However the program sequence remains in the  
memory.  
Press the PROGRAM button, then the PLAY/PAUSE  
button to play the  
programmed sequence again.  
7.) To cancel the programmed sequence from the memory press the STOP  
button while in programming mode.  
The programmed sequence may also be canceled by removing the disc,  
changing function to TUNER  
, or shutting the system ‘off’.  
Program Repeat Playback  
You can use the Program and Repeat features together to continuously repeat a  
programmed sequence of tracks.  
First, program the desired tracks according to Steps 1 through 5 on page 14.  
When Programmed Playback begins press the REPEAT button twice to activate  
the All Tracks Repeat feature.  
PROGRAM  
REPEAT  
FM STEREO  
PLAY/PAUSE  
The REPEAT Indicator lights and all the tracks in your  
programmed sequence will be repeated continuously.  
To cancel Programmed Repeat Playback press the STOP button until both the  
PROGRAM and REPEAT Indicators go ‘Off’.  
RANDOM Playback  
This feature allows you to play all the tracks on a disc in random order.  
Load the disc as usual and wait until the display shows the total playing time and  
number of tracks.  
Press the RANDOM button on front panel. The tracks will be played in random  
order. After all tracks have played the player stops and the display again shows  
the total playing time and number of tracks.  
To cancel Random playback, press the STOP button.  
13  
MS7616_061404.p65  
15  
14/6/2004, 11:00  
 
PHONES Jack  
Connect a set of stereo headphones (not included) with a 3.5mm mini plug to the  
PHONES jack on front panel, for private listening without disturbing others.  
Before putting on the headphones reduce the VOLUME control to a low level, then  
put the headphones on and graduallyincrease the VOLUME control to a comfortable  
listening level.  
The speakers are automatically disconnected when headphones are connected to  
the PHONES jack.  
14  
MS7616_061404.p65  
16  
14/6/2004, 11:00  
 
CARE AND MAINTENANCE  
COMPACT DISC CARE  
• To remove a disc from its storage case, press down on the center of the case  
and lift the disc out, holding it carefully by the edges.  
• Fingerprints and dust should be carefully wiped off the disc’s recorded surface  
with a soft cloth.Unlike conventional records, compact discs have no grooves  
to collect dust and microscopic debris, so gently wiping with a soft cloth should  
remove most particles. Wipe in a straight line from the inside to the outside of  
the disc. Small dust particles and light stains will have absolutely no effect on  
reproduction quality.  
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents  
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.  
• Never write on or affix labels to the surface of compact discs.  
CARE OF THE CABINET  
If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax,  
polish sprays, or abrasive cleaners on the cabinet.  
CAUTION  
Never allow any water or other liquids to get inside the unit while cleaning.  
820-M31600050-J25  
15  
MS7616_061404.p65  
17  
14/6/2004, 11:00  
 

Infinity Portable Speaker IL25c User Manual
Jenn Air Double Oven W27400 User Manual
John Deere Lawn Mower GM2060 User Manual
JVC CD Player XL V230BK User Manual
JVC DVD Player PCX290 User Manual
Kenmore Washer 26842 User Manual
Kenwood Car Video System KVT 534DVDM User Manual
KitchenAid Double Oven KEBS277SSS03 User Manual
Knoll Switch US4 User Manual
Kobe Range Hoods Ventilation Hood IS2036GS User Manual